AVE Video Serial Synchronous ATM Interface VSSI-PRO Uživatelský manuál Strana 31
- Strana / 138
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
ADPRO FastTrace-R by Xtralis Installation and User Manual
Doc 13972_03 19
3. To check the defaults, select the FT-R default site entry and click Edit. The Site
Configuration details are shown with the default values, as follows:
Figure 23: Default Ethernet Site Configuration
Figure 24: Default Serial Site Configuration
2.8 FastTrace-R Configuration
1. Before powering the FastTrace-R unit on, check that the factory DIP-Switch settings are
correct refer to Section 3 for more details.
The location of the DIP-Switch is on the rear of the FastTrace-R unit at the bottom,
underneath the camera connections and next to the monitor connector.
2. Set the DIP-Switch 10 to the appropriate video standard for the region:
- (ON - NTSC, OFF - PAL).
3. Ensure the airflow vents into the side of the FastTrace-R unit are not blocked.
4. Connect the crossover Ethernet cable between the FastTrace-R Ethernet port and the PC’s
Ethernet port or the null modem cable between the Comm2 port and the PC’s serial comms
port.
5. Once DIP-Switch settings are verified and all cables are connected, plug in the mains
power cable.
- ADPRO FastTrace-R 1
- Installation and 1
- User Manual 1
- Contact Us 5
- Declaration of Conformity 6
- Contents 7
- List of Figures 9
- Doc. 13972_03 10
- List of Tables 11
- 1 Introduction 13
- 2 Doc. 13972_03 14
- 2.1 Physical Location 15
- Instructions 16
- 2.3.2 Static Discharge 17
- 2.3.3 Grounding Requirements 17
- 2.4 Unpacking the FastTrace-R 18
- 2.5 Mounting the FastTrace-R 19
- 2.7 Setting up the PC 20
- Doc 13972_03 9 21
- Doc 13972_03 11 23
- Doc 13972_03 13 25
- Null-modem Cable Wiring 27
- Doc 13972_03 17 29
- 2.8 FastTrace-R Configuration 31
- Doc 13972_03 21 33
- 2.10 Adding a New Site 35
- 2.12.2 Front Panel LED 37
- 2.14 Firewall Configuration 38
- 3 FastTrace-R Connectors 39
- 3.1 Power Connection 40
- 3.2.2 COMMS 2 41
- 3.3 Audio 43
- 'AUDIO' 44
- 9-pin DECA Connector 44
- 3.3.3 Audio Configuration 45
- 3.3.4 Zoned Audio 46
- 3.4 Video Input Connections 47
- 3.5 Video Output 49
- 3.6 Configuration Switches 49
- 3.7 Alarm Inputs 51
- Doc 13972_03 41 53
- 3.8 Control Outputs 54
- 3.9 PTZ Connection 55
- 3.9.1 PTZ Port Setup 57
- 3.11 Data Connection 59
- 3.12.4 Push to Talk - Pin 7 61
- 3.12.6 Fault Relay 61
- 4 Programming FastTrace-R 63
- Doc 13972_03 53 65
- 4.3.3 Site Details 67
- 4.3.4 Date/Time Settings 68
- Doc 13972_03 57 69
- 58 Doc 13972_03 70
- 4.3.5 Licensing 71
- 4.3.6 Communications 72
- IP Address for this Unit 73
- Subnet Mask 74
- Default Gateway 74
- Video Data Rate 74
- Doc 13972_03 63 75
- Modem/TA Model 76
- Line Type 76
- Data Rate 76
- Dial Time 76
- Answer Rings 76
- Initialisation String 77
- Redcare Setting 77
- Doc 13972_03 67 79
- Base Port Number 80
- Connection Timeout 80
- Enable WAN Optimisation 80
- PPP Settings 80
- 4.3.7 Connected Equipment 81
- 4.3.8 Cameras 82
- Camera Settings 83
- General Tab 84
- PTZ Settings 85
- Activity Detection Tab 87
- Contrast Monitoring Tab 88
- 4.3.9 Monitor 89
- 4.3.10 Transaction Devices 89
- 4.3.11 Transparent Data Port 90
- Baud Rate 91
- Data Bits 91
- Stop Bits 91
- Flow Control 91
- 4.3.12 Alarm Inputs 92
- 4.3.13 Presidium Inputs 93
- Presidium Input Settings 94
- 4.3.14 Control Outputs 95
- Control Output Settings 96
- 4.3.15 Audio 97
- 4.3.16 Arming / Disarming 98
- 4.3.17 Operational Behaviour 99
- Camera Recording Information 100
- 4.3.18 Operational Modes 101
- Doc 13972_03 102
- 4.3.19 Audio Behaviour 103
- 4.3.20 Camera Behaviour 104
- Video Capture (tab) 105
- Event Triggers 106
- Alarm Logic 107
- Event Inputs 107
- Event Response 109
- Activate Control Output 110
- Generate Alarm on Video Loss 110
- Record Audio on Event 110
- Doc 13972_03 99 111
- Guard Tour Settings 112
- Doc 13972_03 101 113
- 4.3.22 Entry/Exit Behaviour 115
- 4.3.23 Maintenance 116
- Zone Isolate 117
- SitePulse 118
- 5 Event Log 119
- 5.1 Save the Event Log 120
- Doc 13972_03 109 121
- 110 Doc 13972_03 122
- Doc 13972_03 111 123
- 112 Doc 13972_03 124
- Doc 13972_03 113 125
- 114 Doc 13972_03 126
- 6 FastTrace-R Impounding 127
- 116 Doc 13972_03 128
- Doc 13972_03 117 129
- 118 Doc 13972_03 130
- 8.1 Software Upgrade Process 131
- 9 Specifications 133
- 122 Doc 13972_03 134
- Doc 13972_03 123 135
- 124 Doc 13972_03 136
- Tele met ry 136
- Doc 13972_03 125 137
- 126 Doc 13972_03 138
Související produkty a manuály pro Sítě AVE Video Serial Synchronous ATM Interface VSSI-PRO
Sítě AVE Opto 232 Uživatelský manuál
(33 stránky)
(33 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.093 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce